Bbk-performance 1737 Manuel d'utilisateur
Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Bbk-performance 1737. BBK Performance 1737 User Manual Manuel d'utilisatio
- Page / 2
- Table des matières
- MARQUE LIVRES
Noté. / 5. Basé sur avis des utilisateurs
2005-2009 FORD MUSTANG V-6
2005-2009 FORD MUSTANG GT
COLD AIR INDUCTION SYSTEM
PART #'S 1736/17360/17635/1737
INS-099
INSTALLATION INSTRUCTIONS
www.BBKPERFORMANCE.com
IMPORTANT—All appropriate safety equipment (e.i., gloves, tools) must be used during the installation of this product(s).
BBK Performance, Inc. accepts no responsibility for injuries resulting in the installation of any product(s).
!CAUTION!
ALWAYS USE PROTECTIVE EYEWEAR
Included in this kit: Inlet pipe, coupler hose, hose clamps, air filter, air filter shield, and rubber sealant strip.
(2) M-4 screws.
Tools required: Small flat screwdriver or pick, 1/4" ratchet, 8mm, and 10mm sockets, 2.5mm Allen wrench, T-20 Torx.
Step 1 Disconnect (–) negative battery terminal.
Step 2 Unplug the mass air meter by sliding the red colored locking clip back, and then squeezing the tab on the
connector while pulling it from the mass air meter.
Step 3 Separate the PCV tube from the side of the inlet hose by twisting the green locking clip while pulling it away from the
inlet hose.
Step 4 Loosen the hose clamp that attaches the inlet hose to the throttle body.
Step 5 Remove the bolt that holds the air filter box to the driver side fenderwell.
Step 6 Remove the stock intake hose/air box assembly from the vehicle by lifting the air box straight up and pulling the
inlet hose away from the throttle body.
Step 7 Remove the plunger type fasteners that hold the radiator cover in place by gently prying/lifting the center
(plunger) out, and then prying/lifting the outer portion out. Remove the radiator cover and set it aside.
Step 8 Unbolt the driver side radiator hold down plate, lift it off the radiator top post and set it aside.
Step 9 Place the supplied blue coupler hose over the throttle body opening and secure it with one of the supplied hose
clamps.
Step 10 Remove the 2 Torx screws from the mass air meter and slide the meter out of the stock inlet hose, and then
install it into the BBK inlet pipe using the supplied screws.
Step 11 Slip the inlet pipe/mass air meter assembly all the way through the shield. Place the BBK air filter over the end of
the inlet pipe until it rests against the mass air meter bung. Secure the filter to the inlet pipe by tightening the
supplied hose clamp. The end of the air filter will act as an isolator between the inlet pipe and the shield.
Step 12 Drop the inlet pipe/mass air meter/filter/shield assembly into position by placing the round hole on the front of the
shield over the top post of the radiator and slipping the inlet pipe into the blue coupler hose on the throttle body.
Step 13 Tighten the remaining hose clamp over the blue coupler hose to secure the inlet pipe to the throttle body.
Step 14 Insert the original air box mounting bolt through the tab on the back of the shield and tighten it into the factory
speed clip.
1
2
Résumé du contenu
Page 1 - COLD AIR INDUCTION SYSTEM
2005-2009 FORD MUSTANG V-62005-2009 FORD MUSTANG GTCOLD AIR INDUCTION SYSTEMPART #'S 1736/17360/17635/1737INS-099INSTALLATION INSTRUCTIONSwww.BBK
Page 2 - SPECIAL NOTE
Step 15 Re-install the radiator hold down plate and tighten. Step 16 Starting at the radiator hold down plate, place the supplied rubber sealant strip
Produits connexes et manuels pour Pour la voiture Bbk-performance 1737
(2 pages)© 2020, manymanuals.fr. Tous droits réservés | 1.127 s |
Manymanuals.com
Manymanuals.de
Manymanuals.fr
Manymanuals.it
Manymanuals.pl
Manymanuals.cz
Manymanuals.es
Manymanuals-pt.com
Commentaires sur ces manuels